KYK MegaTamir T902 | Fast-Curing Epoxy Acrylate Chemical Anchor and Installation Adhesive

Product Description

KYK MegaTamir T902 is a two-component, styrene-free epoxy acrylate chemical anchoring and installation adhesive designed for high-performance fastening applications.

Its fast-curing formulation quickly develops high mechanical strength, providing secure anchoring in concrete, natural stone, brick, metal, and wood substrates. The low-odor, environmentally friendly formula can be applied using a standard cartridge gun, making it a practical solution for both professional contractors and industrial applications.

KYK MegaTamir T902 delivers reliable, long-lasting anchoring performance for structural and non-structural installations.

Application Areas

KYK MegaTamir T902 is suitable for a wide variety of anchoring and installation applications, including:

Heavy-duty anchoring in concrete and natural stone
Rebar installation and structural strengthening applications
Anchoring threaded rods, bolts, studs, anchors, and steel profiles
Fixing components in solid stone, marble, and brick substrates
Installation of metal and timber structures
Plumbing installations, pipe supports, façade fixing systems, and cable trays
Installation of staircases, handrails, guardrails, and window systems

It is widely used in residential, commercial, industrial, and infrastructure projects requiring high-strength anchoring.

Advantages of KYK MegaTamir T902

Feature	Benefit
Fast curing	Develops high mechanical strength in a short time
Styrene-free formulation	Low odor and environmentally friendly
High chemical resistance	Resistant to acids, alkalis, and salt solutions
Thixotropic consistency	Does not sag on vertical or overhead applications
Standard cartridge gun application	No special dispensing equipment required
Color stability	Maintains its gray appearance over time
Suitable for solid and hollow substrates	Performs effectively on concrete, brick, and stone

Technical Specifications

Property	Value
Chemical base	Two-component epoxy acrylate
Color	Gray
Resin density	1.61 ± 0.01 kg/cm³
Hardener density	1.46 ± 0.01 kg/cm³
Application temperature	+5°C to +35°C
Full curing time (20°C)	Approximately 7 days
Curing time at 5°C	120 minutes
Curing time at 20°C	45 minutes
Curing time at 35°C	15 minutes
Application equipment	Cartridge gun and drill
Standard	TS EN 1504-3
Certification	CE Certified
Packaging	300 ml cartridge (A+B), 12 cartridges per carton
Shelf life	18 months in original unopened packaging

Application Instructions

Surface Preparation

Proper substrate preparation is essential for optimum anchoring performance.

Drill the anchor hole using a hammer drill.
Remove all dust and debris with compressed air.
Ensure the hole is completely free of dust, oil, moisture, and loose particles.
Reinforcing bars or anchor rods must be clean and free from rust and contaminants before installation.

Application Steps

Remove the cartridge cap and cut the foil seal.
Attach the static mixing nozzle and insert the cartridge into a standard dispensing gun.
Dispense a small amount of material until a uniform gray color is achieved.
Fill approximately two-thirds (2/3) of the anchor hole with adhesive.
Insert the anchor rod while slowly rotating it to ensure complete encapsulation.
Excess material flowing out of the hole indicates proper filling.
Apply the structural load only after the adhesive has fully cured.

Estimated Material Consumption

(Based on C30 concrete with ribbed reinforcing bars)

Rebar Diameter (mm)	Minimum Hole Diameter (mm)	Hole Depth (mm)	Approximate Consumption (ml/hole)
8	10	80	5
10	12	90	8
12	14	110	14
16	18	125	26
20	24	170	49
24	28	210	173

Actual consumption may vary depending on substrate conditions and installation requirements.

Application Recommendations

Do not use the initial material discharged from the mixing nozzle, as it is not fully mixed.
Do not use expired material.
Avoid application under direct sunlight.
Lower temperatures increase curing time, while higher temperatures accelerate curing.
Do not apply to weak or unsound substrates.
Ensure adequate ventilation during indoor applications.

Frequently Asked Questions (FAQ)

What is KYK MegaTamir T902?

KYK MegaTamir T902 is a fast-curing, two-component epoxy acrylate chemical anchoring adhesive designed for high-strength fastening and installation applications.

Where can it be used?

It is suitable for anchoring reinforcing bars, threaded rods, bolts, profiles, and other fixing elements in concrete, stone, brick, wood, and metal substrates.

How is it applied?

The adhesive is dispensed using a standard cartridge gun, filling approximately two-thirds of the drilled hole before inserting the anchor while rotating it slowly.

How long does it take to cure?

Typical curing times are:

120 minutes at 5°C
45 minutes at 20°C
15 minutes at 35°C

Full curing is achieved after approximately 7 days at 20°C.

Is the product environmentally friendly?

Yes. KYK MegaTamir T902 is styrene-free, making it a low-odor and environmentally friendly anchoring solution.

Conclusion

KYK MegaTamir T902 provides fast curing, outstanding adhesion, and exceptional mechanical performance for professional chemical anchoring applications.

Its styrene-free epoxy acrylate technology ensures reliable installation of heavy-duty anchors, reinforcing bars, threaded rods, and structural fixing systems across a wide range of construction and industrial projects.

KYK MegaTamir T902 — Fast Curing, Superior Bonding, Reliable Anchoring.